Dataset Search

The presence of free fatty acids interferes with the conversion of plant oils to biodiesel. Four strong and weak base resins were evaluated for the removal of free fatty acids (FFA) from oil. Amberlite FPA 51 showed the highest adsorption capacity of FFA. A resin concentration above 3% could enable a higher percentage FFA adsorption. The adsorption process fitted a pseudo-first-order kinetic model and achieved equilibrium in approximately 8 h. A full factorial design was used to optimize the resin and FFA concentrations at a fixed temperature (40° C). A ratio of resin to fatty acid concentrations above 1.875 was sufficient for 70% adsorption and the amount adsorbed continued to increase with further added resin. A two-step washing of resin using hexane and ethanol recovered approximately 67.55% ± 4.05% of the initially added fatty acid. The resin that was used was regenerated with 5% NaOH and re-used for a minimum of three consecutive cycles. However, the adsorption capacity diminished to 75% of the initial cycle in cycles 2 and 3. Thus, the work presents a resin-based process for deacidification of oil to reduce fatty acid content of oil for biodiesel production.

Use of corn fractionation techniques in dry grind process increases the number of coproducts, enhances their quality and value, generates feedstock for cellulosic ethanol production and potentially increases profitability of the dry grind process. The aim of this study is to develop process simulation models for eight different wet and dry corn fractionation techniques recovering germ, pericarp fiber and/or endosperm fiber, and evaluate their techno-economic feasibility at the commercial scale. Ethanol yields for plants processing 1113.11 MT corn/day were 37.2 to 40 million gal for wet fractionation and 37.3 to 31.3 million gal for dry fractionation, compared to 40.2 million gal for conventional dry grind process. Capital costs were higher for wet fractionation processes ($92.85 to $97.38 million) in comparison to conventional ($83.95 million) and dry fractionation ($83.35 to $84.91 million) processes. Due to high value of coproducts, ethanol production costs in most fractionation processes ($1.29 to $1.35/gal) were lower than conventional ($1.36/gal) process. Internal rate of return for most of the wet (6.88 to 8.58%) and dry fractionation (6.45 to 7.04%) processes was higher than the conventional (6.39%) process. Wet fractionation process designed for germ and pericarp fiber recovery was most profitable among the processes.

DNA aptamers have been widely used as biosensors for detecting a variety of targets. Despite decades of success, they have not been applied to monitor any targets in plants, even though plants are a major platform for providing oxygen, food, and sustainable products ranging from energy fuels to chemicals, and high-value products such as pharmaceuticals. A major barrier to progress is a lack of efficient methods to deliver DNA into plant cells. We herein report a thiol-mediated uptake method that more efficiently delivers DNA into Arabidopsis and tobacco leaf cells than another state-of-the-art method, DNA nanostructures. Such a method allowed efficient delivery of a glucose DNA aptamer sensor into Arabidopsis for sensing glucose. This demonstration opens a new avenue to apply DNA aptamer sensors for functional studies of various targets, including metabolites, plant hormones, metal ions, and proteins in plants for a better understanding of the biodistribution and regulation of these species and their functions.

We present a new strategy for the production of a δ-lactam from glucose that integrates biological production of triacetic acid lactone (TAL, 4-hydroxy-6-methyl-2H-2-one) with catalytic transformation of TAL into 6-methylpiperidin-2-one (MPO) through metabolic engineering, isomerization, amination, and catalytic hydrogenation/hydrogenolysis. We developed a sustainable and antibiotic-free fed-batch fermentation using genetically modified Rhodotorula toruloides IFO0880. This process achieved a yield of 2-hydroxy-6-methyl-4H-pyran-4-one (2H4P) at 0.05 g/g of glucose, corresponding to a 9.9 g/L titer. By adjusting the pH of the fermentation broth to 2, 2H4P was quantitatively converted into TAL. The TAL in the fermentation broth was directly converted by aminolysis into 4-hydroxy-6-methylpyridin-2(1H)-one (HMPO), which achieved an 18.5% yield with 94.3% purity. The HMPO yield was lower in the fermentation broth than in a clean feedstock (32.2%), suggesting that the biological impurities are inhibitors in this reaction. Further investigation revealed that lower pH levels and reduced TAL concentrations in the fermentation broth significantly decreased HMPO yields. Subsequently, the precipitated HMPO was filtered and dried and then subjected to the final catalytic conversion in H2O solvent, achieving a MPO yield of 91.8%. This integrated approach demonstrated the direct use of TAL in the filtered aqueous fermentation broth without the need to isolate TAL.

We developed a new application of isotopic gas exchange which couples a tunable diode laser absorption spectroscope (TDL) with a leaf gas exchange system, analyzing leakiness through induction of C4 photosynthesis on dark to high-light transitions. The youngest fully expanded leaf was measured on 40-45 day-old maize(B73) and sorghum (Tx430). Detail definition of each variable in raw Li-6400XT and Li-6800 (in "Original_data_AND_Data_processing_code.zip") is summarized in: <a href="https://www.licor.com/env/support/LI-6800/topics/symbols.html#const">https://www.licor.com/env/support/LI-6800/topics/symbols.html#const</a>

5-hydroxymethyl furfural (HMF) and furfurals are DOE-listed platform chemicals that can be derived from the renewable carbon in the lignocellulosic biomasses and have the potential to replace petroleum-derived alternatives. High substrate cost and use of expensive solvents limit the economic feasibility of bio-based HMF production on an industrially relevant scale. The study presents an experimental optimized condition that maximizes the chemical-free production of HMF and furfurals without lowering the yield of total fermentable sugars from Saccharum bagasse. Hydrothermal pretreatment at 210 °C for 15 min yielded approximately 10%, 12%, and 46% of HMF, furfurals, and fermentable sugars per gram of dry biomass, respectively. Additionally, the study proposes a consolidated bioprocess model to produce and recover four high-value bioproducts i.e., HMF, furfurals, ethanol, and acetic acid based on the experimental results and evaluates its technoeconomic feasibility considering HMF as the main product. The minimum selling price (MSP) of HMF was estimated to be 930.6 USD/t which is competitive with its petroleum-derived precursor alternative p-xylene (1,113 USD/t). The sensitivity analysis performed for the process parameters suggests that pretreatment cost and revenues from coproducts immensely influence the MSP of HMF. The preliminary technoeconomic analysis performed on the consolidated bioprocess design indicates that additional revenue streams from diversified coproducts in biorefineries aid in lowering the MSP of high-value bioproducts.

This dataset contains the emulated global multi-model urban climate projections under RCP 8.5 and RCP 4.5 used in the article "Global multi-model projections of local urban climates" (https://www.nature.com/articles/s41558-020-00958-8). Details about this dataset and the local urban climate emulator are described in the article. This dataset documents the monthly mean projections of urban temperatures and urban relative humidity of 26 CMIP5 Earth system models (ESMs) from 2006 to 2100 across the globe. This dataset may be useful for multiple communities regarding urban climate change, impacts, vulnerability, risks, and adaptation applications.

Aerial imagery utilized as input in the manuscript "Deep convolutional neural networks exploit high spatial and temporal resolution aerial imagery to predict key traits in miscanthus" . Data was collected over M. Sacchariflorus and Sinensis breeding trials at the Energy Farm, UIUC in 2020. Flights were performed using a DJI M600 mounted with a Micasense Rededge multispectral sensor at 20 m altitude around solar noon. Imagery is available as tif file by field trial and date (10). The post-processing of raw images into orthophoto was performed in Agisoft Metashape software. Each crop surface model and multispectral orthophoto was stacked into an unique raster stack by date and uploaded here. Each raster stack includes 6 layers in the following order: Layer 1 = crop surface model, Layer 2 = Blue, Layer 3 = Green, Layer 4 = Red, Layer 5 = Rededge, and Layer 6 = NIR multispectral bands. Msa raster stacks were resampled to 1.67 cm spatial resolution and Msi raster stacks were resampled to 1.41 cm spatial resolution to ease their integration into further analysis. 'MMDDYYYY' is the date of data collection, 'MSA' is M. Sacchariflorus trial, 'MSI' is Miscanthus Sinensis trial, 'CSM' is crop surface model layer, and 'MULTSP' are the five multispectral bands.

Corbicula spp. are one of the most prolific aquatic invasive species in the world and can have negative effects on aquatic ecosystems. We performed qualitative field surveys, examined literature accounts and natural history museum holdings, and accessed citizen science data sources to document the distribution of Corbicula in Mexico and shared drainages. Through 26 publications (N = 127 records), 312 museum holdings, and 446 iNaturalist records, we documented 885 records pertaining to Corbicula in Mexico and shared drainages. The first record of the species in Mexico was in 1969, and it has since been reported from 26 of the 32 Mexican states and most of the major river basins throughout the country. However, we suggest Corbicula is more prevalent in Mexico than we report in this work as it is often under sampled / under reported.

This repository contains the the data and code to recreate the simulations in "High Costs of GHG Abatement with Electrifying the Light-Duty Vehicle Fleet with Heterogeneous Preferences of Vehicle Consumers." The model can be run by calling the bash file in the SLURM environment with parameters set for different scenarios. BEPEAM-E model details: (1) the "Main.gms" file in GAMS format that contains the initiating stage settings with input and main optimization model (2) the "output.gms" file in GAMS format that prepare the output file from BEPAM model. (3) the rest are the intermediate input files for model to generate the input and output files for the model. (4) Four bash files are the script file that call the GAMS model on the HPC that includes both HPC environment and the scenario settings. Four bash files are uploaded corresponding to 4 scenarios

The optimal flowering time for bioenergy crop miscanthus is essential for environmental adaptability and biomass accumulation. However, little is known about how genes controlling flowering in other grasses contribute to flowering regulation in miscanthus. Here, we report on the sequence characterization and gene expression of Miscanthus sinensisGhd8, a transcription factor encoding a HAP3/NF-YB DNA-binding domain, which has been identified as a major quantitative trait locus in rice, with pleiotropic effects on grain yield, heading date and plant height. In M. sinensis, we identified two homoeologous loci, MsiGhd8A located on chromosome 13 and MsiGhd8B on chromosome 7, with one on each of this paleo-allotetraploid species’ subgenomes. A total of 46 alleles and 28 predicted protein sequence types were identified in 12 wild-collected accessions. Several variants of MsiGhd8 showed a geographic and latitudinal distribution. Quantitative real-time PCR revealed that MsiGhd8 expressed under both long days and short days, and MsiGhd8B showed a significantly higher expression than MsiGhd8A. The comparison between flowering time and gene expression indicated that MsiGhd8B affected flowering time in response to day length for some accessions. This study provides insight into the conserved function of Ghd8 in the Poaceae, and is an important initial step in elucidating the flowering regulatory network of Miscanthus.

Miscanthus × giganteus (Miscanthus) is a warm-season perennial grass grown for bioenergy feedstock production. Nitrogen (N) fertilizer management is crucial for the sustainability of Miscanthus production. In our two-year study (2018 and 2019), we investigated the role of vegetation indices (VIs) in evaluating N fertilization (0 N, 56 N, 112 N, and 168 N kg ha−1) impacts on Miscanthus biomass yield and stand health. The flight campaigns were conducted early, middle, and late during the summer growing season. Among the VIs, mid-summer growing season NDRE provided the best prediction of fresh biomass (R2 = 0.87 and 0.97) and dry biomass (R2 = 0.89 and 0.97) in 2018 and 2019, respectively. The VIs generally showed that it was possible to distinguish between 0 N and 168 N treatments, but neither 0 N and 56 N kg ha−1 nor 112 N and 168 N kg ha−1 could be separated. The results from this study highlight the importance of moderate application of N (112 kg N ha−1) in improving and maintaining the stand health and biomass yield of Miscanthus over time and suggest that mid-summer growing season VIs, NDRE in particular, can be useful for assessment of Miscanthus stand health and biomass yield.

The aim of this study was to determine carbohydrate recovery from hemp for ethanol production and quantify biodiesel from TAG (triacylglycerol) present in hemp. The structural composition of five different hemp varieties (Seward County-SC, York County-YC, Loup County-LC, 19 m96136-19 m, and CBD Hemp-CBD) were analyzed. Concentration of glucan and xylan ranged between 32.63 to 44.52% and 10.62 to 15.48% respectively. The biomass was then pretreated with Liquid hot water followed by disk milling and then hydrolyzed enzymatically to yield monomeric sugars. High glucose (63-85%) and xylose (73-88%) recovery was achieved. Lipids were extracted from hemp using hexane and isopropanol and then transesterified to produce biodiesel. Approximately, 50% of total fatty acids in SC, LC, and CBD hemp were linoleic acid. Palmitic acid was present between 32 to 50% in varieties YC and 19 m. Highest TAG concentration at 25% of total lipids was observed in CBD hemp. The analysis on lipid composition and high sugar recovery demonstrates hemp as a potential bioenergy crop for ethanol and biodiesel coproduction.

The plant-sourced polyketide triacetic acid lactone (TAL) has been recognized as a promising platform chemical for the biorefinery industry. However, its practical application was rather limited due to low natural abundance and inefficient cell factories for biosynthesis. Here, we report the metabolic engineering of oleaginous yeast Rhodotorula toruloides for TAL overproduction. We first introduced a 2-pyrone synthase gene from Gerbera hybrida (GhPS) into R. toruloides and investigated the effects of different carbon sources on TAL production. We then systematically employed a variety of metabolic engineering strategies to increase the flux of acetyl-CoA by enhancing its biosynthetic pathways and disrupting its competing pathways. We found that overexpression of ATP-citrate lyase (ACL1) improved TAL production by 45% compared to the GhPS overexpressing strain, and additional overexpression of acetyl-CoA carboxylase (ACC1) further increased TAL production by 29%. Finally, we characterized the resulting strain I12-ACL1-ACC1 using fed-batch bioreactor fermentation in glucose or oilcane juice medium with acetate supplementation and achieved a titer of 28 or 23 g/L TAL, respectively. This study demonstrates that R. toruloides is a promising host for the production of TAL and other acetyl-CoA-derived polyketides from low-cost carbon sources.

This dataset contains genotypic and phenotypic data, R scripts, and the results of analysis pertaining to a multi-location field trial of Miscanthus sinensis. Genome-wide association and genomic prediction were performed for biomass yield and 14 yield-component traits across six field trial locations in Asia and North America, using 46,177 single-nucleotide polymorphism (SNP) markers mined from restriction site-associated DNA sequencing (RAD-seq) and 568 M. sinensis accessions. Genomic regions and candidate genes were identified that can be used for breeding improved varieties of M. sinensis, which in turn will be used to generate new M. xgiganteus clones for biomass.

Data and code supporting the paper titled "Estimating the Electric Vehicle Charging Demand of Multi-Unit Dwelling Residents in the United States" by Xi Cheng and Eleftheria Kontou at the University of Illinois Urbana-Champaign. The data and the code enable analytics and assessment of multi-unit dwelling residents travel patterns and their electric vehicle charging demand.

Elevated tropospheric ozone concentration (O3) significantly reduces photosynthesis and productivity in several C4 crops including maize, switchgrass and sugarcane. However, it is unknown how O3 affects plant growth, development and productivity in sorghum (Sorghum bicolor L.), an emerging C4 bioenergy crop. Here, we investigated the effects of elevated O3 on photosynthesis, biomass and nutrient composition of a number of sorghum genotypes over two seasons in the field using free-air concentration enrichment (FACE), and in growth chambers. We also tested if elevated O3 altered the relationship between stomatal conductance and environmental conditions using two common stomatal conductance models. Sorghum genotypes showed significant variability in plant functional traits, including photosynthetic capacity, leaf N content and specific leaf area, but responded similarly to O3. At the FACE experiment, elevated O3 did not alter net CO2 assimilation (A), stomatal conductance (gs), stomatal sensitivity to the environment, chlorophyll fluorescence and plant biomass, but led to reductions in the maximum carboxylation capacity of phosphoenolpyruvate and increased stomatal limitation to A in both years. These findings suggest that bioenergy sorghum is tolerant to O3 and could be used to enhance biomass productivity in O3 polluted regions.

The dataset contains processed model fields used to generate data, figures and tables in the Journal of Geophysical Research article "Investigating the linear dependence of direct and indirect radiative forcing on emission of carbonaceous aerosols in a global climate model." The processed data are monthly averaged cloud properties (CCN, CDNC and LWP) and forcing variables (DRF and IRF) at original CAM5 spatial resolution (1.9° by 2.5°). Raw model output fields from CAM5 simulations are available through NERSC upon request. Please find more detailed information in the ReadMe file.

Supplementary data tables for the dissertation "Hybridization dynamics and population genomics of a Manacus hybrid zone." This work focuses on the dynamics of hybridization over time in two species of tropical birds, the golden-collared manakin (Manacus vitellinus) and white-collared manakin (Manacus candei) comparing data from historical museum samples and contemporary wild-caught birds. Table A1 contains the sample metadata for the Manacus Restriction site-associated DNA sequencing dataset used in the dissertation with associated NCBI Biosample Accession numbers, Smithsonian Museum of Natural History number (where applicable), sample IDs, sampling site locations, and sample information of year the sample was taken, age, and sex. Table A6 contains phenotypic measurements of male plumage traits of manakins used in cline analyses to assess hybrid zone movement over time in historical and contemporary datasets, including beard length (mm), epaulet width (mm), tail length (mm), collar color (nm), and belly color (nm). Table A7 contains a summary of male plumage measurements across the hybrid zone. Table C1 contains a list of annotated protein coding genes in candidate regions of interest in Manacus genomes using outlier regions of genomic divergence, linkage disequilibrium, and enrichment of parental private alleles.

This data set includes information on mixing metric values and distances to determine the average length scale, rates and variability of mixing downstream of 43 river confluences for 150 mixing events. The file "pmx_all data.csv" contains confluence names, the number of events per confluence site, and Pmx values measured at various actual and dimensionless downstream distances. The file "pmx_binned data.csv" provides mean Pmx values within 0.5-unit dimensionless distance bins.

The dominant strategy for tailoring the chain-length distribution of free fatty acids (FFA) synthesized by heterologous hosts is expression of a selective acyl-acyl carrier protein (ACP) thioesterase. However, few of these enzymes can generate a precise (greater than 90% of a desired chain-length) product distribution when expressed in a microbial or plant host. The presence of alternative chain-lengths can complicate purification in situations where blends of fatty acids are not desired. We report the assessment of several strategies for improving the dodecanoyl-ACP thioesterase from the California bay laurel to exhibit more selective production of medium-chain free fatty acids to near exclusivity. We demonstrated that matrix-assisted laser desorption/ionization time-of-flight mass spectrometry (MALDI-ToF MS) was an effective library screening technique for identification of thioesterase variants with favorable shifts in chain-length specificity. This strategy proved to be a more effective screening technique than several rational approaches discussed herein. With this data, we isolated four thioesterase variants which exhibited a more selective FFA distribution over wildtype when expressed in the fatty acid accumulating E. coli strain, RL08. We then combined mutations from the MALDI isolates to generate BTE-MMD19, a thioesterase variant capable of producing free fatty acids consisting of 90% of C12 products. Of the four mutations which conferred a specificity shift, we noted that three affected the shape of the binding pocket, while one occurred on the positively charged acyl carrier protein landing pad. Finally, we fused the maltose binding protein (MBP) from E. coli to the N – terminus of BTE-MMD19 to improve enzyme solubility and achieve a titer of 1.9 g per L of twelve-carbon fatty acids in a shake flask.

Dataset compiled by Yushu Xia and Michelle Wander for the Soil Health Institute. Data were recovered from peer reviewed literature reporting results for three soil quality indicators (SQIs) (β-glucosidase (BG), fluorescein diacetate (FDA) hydrolysis, and permanganate oxidizable carbon (POXC)) in terms of their relative response to management where soils under grassland cover, no-tillage, cover crops, residue return and organic amendments were compared to conventionally managed controls. Peer-reviewed articles published between January of 1990 and May 2018 were searched using the Thomas Reuters Web of Science database (Thomas Reuters, Philadelphia, Pennsylvania) and Google Scholar to identify studies reporting results for: “β-glucosidase”, “permanganate oxidizable carbon”, “active carbon”, “readily oxidizable carbon”, and “fluorescein diacetate hydrolysis”, together with one or more of the following: “management practice”, “tillage”, “cover crop”, “residue”, “organic fertilizer”, or “manure”. Records were tabulated to compare SQI abundance in soil maintained under a control and soil aggrading practice with the intent to contribute to SQI databases that will support development of interpretive frameworks and/or algorithms including pedo-transfer functions relating indicator abundance to management practices and site specific factors. Meta-data include the following key descriptor variables and covariates useful for development of scoring functions: 1) identifying factors for the study site (location, year of initiation of study and year in which data was reported), 2) soil textural class, pH, and SOC, 3) depth and timing of soil sampling, 4) analytical methods for SQI quantification, 5) units used in published works (i.e. equivalent mass, concentration), 6) SQI abundances, and 7) statistical significance of difference comparisons. *Note: Blank values in tables are considered unreported data.

This dataset contains all the necessary information to recreate the study presented in the paper entitled "Learning coagulation processes with combinatorially-invariant neural networks". This consists of (1) the aggregated output files used for machine learning, (2) the machine learning codes used to learn the presented models, (3) the PartMC model source code that was used to generate the simulation data and (4) the Python scripts used construct the scenario library for training and testing simulations. This data was used to investigate a method (combinatorally-invariant neural network) for learning the aerosol process of coagulation. This data may be useful for application of other methods.

This dataset provides instructions for procedures to use heat transfer analyses to estimate thermal conditions in artificial roosts for bats. The dataset contains scripts to employ in the program GNU Octave, example meteorology data, and example text files specifying roost dimensions and material properties.

Miscanthus is a close relative of saccharum and a potentially valuable genetic resource for improving sugarcane. Differences in flowering time within and between miscanthus and saccharum hinders intra- and interspecific hybridizations. A series of greenhouse experiments were conducted over three years to determine how to synchronize flowering time of saccharum and miscanthus genotypes. We found that day length was an important factor influencing when miscanthus and saccharum flowered. Sugarcane could be induced to flower in a central Illinois greenhouse using supplemental lighting to reduce the rate at which days shortened during the autumn and winter to 1 min d-1, which allowed us to synchronize the flowering of some sugarcane genotypes with Miscanthus genotypes primarily from low latitudes. In a complementary growth chamber experiment, we evaluated 33 miscanthus genotypes, including 28 M. sinensis, 2 M. floridulus, and 3 M. ×giganteus collected from 20.9° S to 44.9° N for response to three day lengths (10 h, 12.5 h, and 15 h). High latitude-adapted M. sinensis flowered mainly under 15 h days, but unexpectedly, short days resulted in short, stocky plants that did not flower; in some cases, flag leaves developed under short days but heading did not occur. In contrast, for M. sinensis and M. floridulus from low latitudes, shorter day lengths typically resulted in earlier flowering, and for some low latitude genotypes, 15 h days resulted in no flowering. However, the highest ratio of reproductive shoots to total number of culms was typically observed for 12.5 h or 15 h days. Latitude of origin was significantly associated with culm length, and the shorter the days, the stronger the relationship. Nearly all entries achieved maximal culm length under the 15 h treatment, but the nearer to the equator an accession originated, the less of a difference in culm length between the short-day treatments and the 15 h day treatment. Under short days, short culms for high-latitude accessions was achieved by different physiological mechanisms for M. sinensis genetic groups from the mainland in comparison to those from Japan; for mainland accessions, the mechanism was reduced internode length, whereas for Japanese accessions the phyllochron under short days was greater than under long days. Thus, for M. sinensis, short days typically hastened floral induction, consistent with the expectations for a facultative short-day plant. However, for high latitude accessions of M. sinensis, days less than 12.5 h also signaled that plants should prepare for winter by producing many short culms with limited elongation and development; moreover, this response was also epistatic to flowering. Thus, to flower M. sinensis that originates from high latitudes synchronously with sugarcane, the former needs day lengths >12.5 h (perhaps as high as 15 h), whereas that the latter needs day lengths <12.5 h.